Русская версия
  • Country*:
  • Name*:
  • Company*:
  • E-mail*:
  • Confirm your e-mail*:
  • Phone number:
  • Message*:

* - Required

Send

Shaft Geometry Measurement Machine

The machine is intended for precise measuring of geometric parameters (diameters, ovality, and conicity) of the shaft-type parts.

Field of application: large-scale production.

Get PricingInquires
Models
  • Shaft Geometry Measurement Machine <br/> RF800 Series

    Shaft Geometry Measurement Machine
    RF800 Series

     

    Shaft length, mm from 160 to 750
    Shaft diameter, mm from 5 to 30
    Measurement accuracy, um ±2
    Time of measuring the shaft of the maximum length, s <20
    Sorting "OK/NOK" Yes
    Ability to sort by groups Yes
    See detailed specifications →
Specifications

Shaft Geometry Measurement Machine
RF800 Series

Name of parameter Value
Shaft length, mm 160...750
Shaft diameter, mm 5...30
Accuracy, μm ±1
Time of measuring the shaft of the maximum length, s, no more than 20
Number of controlled shaft zones and their position Programmable value
Maximum shaft weight, kg 2
Measured parameters Diameter, ovality, taper
Sorting "OK"-"NOK" Yes
Ability to sort by groups Yes
Power supply Three-phase alternating current network with frequency of (50 ± 1) Hz, nominal voltage 220 / 380V with a permissible voltage deviation of ±10%.
Power consumption, W 100
Environmental resistance Operating ambient temperature: +1...+35°С
Relative humidity for 25°С: 65%
Operation mode 3 shifts, 6 days a week
Dimensions, mm 380х428х1079
Note! Machine parameters can be changed for a specific task.

 

Operation

The structure of the machine (without protective doors) is illustrated in Figure 3.

The machine contains a frame (1) on which a linear guide (2) of the linear translation system is installed. The linear guide has a carriage (3) driven by a stepper motor (4).

An optical micrometer (5) is installed on the carriage (3). The end sensors (not shown) are used to monitor the end positions of the micrometer. A table with two Morse tapers (6 and 7) is used to install the controlled shaft. The Morse tapers are mounted on a bar (8) located along the the linear guide. One of the end sensors is mounted on the upper taper, the latter can be reinstalled along the bar (8) in order to control the shafts of different lengths.

In addition, the machine has a caliber, which is a part of the upper Morse taper. The caliber is designed for an automatic re-calibration of the micrometer to eliminate the measurement error caused by a change in the temperature of the machine.

The machine contains a mini-computer (9) with a graphic touch screen. The mini-computer has the special software designed to control the machine and to display results. The mini-computer can be built into the machine (as shown in Figure 3), or it can be installed on the special stand (see Figure 4).

The back side of the machine has a power supply 220/24V (10) with a circuit breaker (11), connector for the foot switch (12), USB connector (13) for the USB drive (for example, for data transfer), and the Ethernet connector (14), for example, to connect to the PC.


Figure 3


Figure 4

After the measurement algorithm has been programmed (position and number of controlled zones along the shaft, tolerances, etc. - see the software description), the operator installs a shaft into the machine. After a command from the operator (by the foot switch, or by the softkey on the touch screen), the linear translation system moves the micrometer along the shaft. The data from the micrometer (shaft diameters in two mutually perpendicular cross sections) synchronized with the linear position of the micrometer comes to the computer where the required parameters are calculated (shaft diameter and shaft shape error).

Video

Shaft Geometry Measurement Machine

Search

 

Site sections

More links

© 2001 – 2019 RIFTEK LLC

Logoisky tract, 22, Minsk, Republic of Belarus
TIN 100051163

Tel/fax:  +375 (17) 357-36-57

Mobile:   +375 (29) 655-72-55

E-mail: info@riftek.com

Our partners in other countries

  • Country*:
  • Name*:
  • Company*:
  • E-mail*:
  • Confirm your e-mail*:
  • Phone number:
  • Message*:

* - Required

Send